Quality amplifier based on the ORIGINAL and long discontinued chip, TDA2030A from STM.
In addition to the original chip, the amplifier uses only quality components.

By default, the circuit is assembled using a dividing capacitor at the input, but in most cases it is possible to do without it, with a constant output voltage not exceeding 0.015-0.020V, which is quite normal. And the released quality capacitor can be used to bypass the bipolar electrolytic capacitor in the NF circuit. This inclusion gives a double positive effect: 1 eliminates the influence of the input dividing capacitor; 2 improves the quality of bipolar electrolyte in NF. This is reflected in the sound by increasing the detail on the HF and widening the band to the Bass.
The board provides both connections:
1. Connection with a capacitor - the signal is sent to the contact (IN), the jumper (J) is soldered on the back.
2. Connection without a capacitor - the signal is sent to the contact (IN '), both jumps (J') are soldered on the back side.
Premium version available. It differs in the installation of precision, super-quality components:
Isolation Capacitors - Epcos or WIMA
Resistors - Vishay DALE

Complete with rack with M2 bolts for installation in the housing, as well as mica gaskets, insulating washers and thermal paste for installation on the radiator.

Supply voltage +/- 6V - +/- 18V
Power depends on voltage and current 5-18W
Measurements
Supply voltage bipolar -18V...0...+18V
Load resistance

4 Ohm

Power maximum, W 20
Testing power, W 8
Frequency response (from 40 Hz to 15 kHz), dB +0.01, -0.08
Noise level, dB (A) -101,4
Dynamic range, dB (A) 101,4
THD, % 0,0120
THD + Noise, dB (A) -75,8
IMD + Noise, % 0,0370
IMD at 10 kHz, % 0,0098
Amplifier Measurement Page

TDA2030A (STM) stereo module test report

General characteristics
Amplifier class AB
Built-in protection Yes
Chip TDA2030A
Gain 33
Maximum supply voltage (bipolar / constant) DC 18V
Minimum supply voltage (bipolar / constant) DC 6V
Module size LxWxH, mm

33x50x25

Number of channels mono
Weight, kg

0,030

Write a review

Note: HTML is not translated!
    Bad           Good
Captcha

TDA2030A original from STM, mono amplifier

  • Brands kitON
  • Product Code: M13S-01
  • Availability: In Stock
  • 520.00грн.


Available Options


Related Products

Tags: TDA2030A (STM) ORIGINAL, UP TO 30W AMPLIFIER, MONO AMPLIFIER, BIPOLAR POWER, CLASS AB

Products viewed

Switching power supply 48V 4A, AC-DC converter

Switching power supply 48V 4A, AC-DC converter

AC-DC converter, power supply 220V to 48V 4A is a switching power supply unit that converts the AC v..

770.00грн.

Converter to bipolar voltage with galvanic isolation

Converter to bipolar voltage with galvanic isolation

Stabilized power supply with bipolar voltage from a 12V car network.A complete device for converting..

750.00грн.

Amplifier power supply up to +/- 35V

Amplifier power supply up to +/- 35V

Universal board for a bipolar power supply for low and medium power amplifiers (up to 100 W).Perfect..

670.00грн.

TDA7293 original inverting mono amplifier 110W

TDA7293 original inverting mono amplifier 110W

High-quality inverting amplifier based on the original and very popular TDA 7293 microcircuit. The w..

1,090.00грн.

Featured Articles

Measurement technique

Measurement technique

Any more or less complex electronic device requires a functional check and adjustmentThe audio power amplifier is no exception and measurements of the characteristics of this device are not only a dev..

TDA2030A (STM) measurements

TDA2030A (STM) measurements

Testing device TDA2030A (STM) stereo Sampling mode 24-bit, 48 kHz Interface E-MU1616m Testing chain E-MU1616m>TDA2030A (STM) stereo module>E-MU1616m ..